Low profile Perspex Case For Arduino Uno (HCCASE0006)

Arduino compatible cases
Post Reply
admin
Site Admin
Posts: 787
Joined: Sun Aug 05, 2012 4:02 pm

Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by admin » Thu Feb 26, 2015 11:58 am

Image


Image

Protect your Arduino Uno with this very low cost but stylish case. Made from clear perspex provides access to all the connectors on any Uno that conforms to the Arduino specification including our own version (HCARDU0090) and only adds a slight increase to the overall hight. This allows you to have full access to your Uno whilst working on your project and helps to protect it from accidental damage from lose wires or dropped components. Once your project is complete the case will help show it off in style. Case is compatible with most shields.



Image

Product code: HCCASE0006
Dimensions: 59mm x 55mm x 18.3mm (without fixings)
Material: Clear perspex with stainless steel fixings

Order Yours Here.


GUIDE:
Images show part with protective backing in place. This should be removed before construction.

Step 1...
Image

Step 2...
Image

Step 3...
Image

Step 4...
Image

Step 5...
Image

ILYBTodd
Posts: 18
Joined: Mon Nov 05, 2018 6:20 pm

Re: Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by ILYBTodd » Wed Feb 06, 2019 1:40 am

Just got two of these to go with my 2 UNO Plus and they went together with no fuss, look great and are a good value.

ILYBTodd
Posts: 18
Joined: Mon Nov 05, 2018 6:20 pm

Re: Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by ILYBTodd » Sat Nov 21, 2020 2:27 am

Here's a tip to help with assembly.

I put the nuts on a soft mouse pad and then aligned the corner screws over the top of them and with a small screw driver tightened them part way. The mouse pad holds the nuts enough to keep them from spinning and you don't have to hold them in your fingers to get them started.

Nice design.

ILYBTodd
Posts: 18
Joined: Mon Nov 05, 2018 6:20 pm

Re: Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by ILYBTodd » Fri Nov 27, 2020 12:47 am

Hey Andrew,

Can you produce a UNO+ compatible version of this case?

Something with double wide slots and a window for the extra pinouts near the ICSP pins would be complement the UNO+ nicely.

Let me know when they will be offered and I'll order a hand full. :-)

Todd

ILYBTodd
Posts: 18
Joined: Mon Nov 05, 2018 6:20 pm

Re: Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by ILYBTodd » Fri Nov 27, 2020 12:55 am

Hey Andrew,

Can you produce a UNO+ compatible version of this case?

Something with double wide slots and a window for the extra pinouts near the ICSP pins would complement the UNO+ nicely.

Let me know when they will be offered and I'll order a hand full. :-)

Todd

andrew
Site Admin
Posts: 1043
Joined: Sun Aug 05, 2012 4:15 pm

Re: Low profile Perspex Case For Arduino Uno (HCCASE0006)

Post by andrew » Fri Nov 27, 2020 3:58 pm

Hi Todd, yeah it would be a nice product to stock. The current Uno cases aren't actually our product but we are looking out for a good laser cutting service as we've got quite a few of our own ideas for products requiring laser cut perspex. The biggest issue is that we're in a very competitive market and so anything we have manufactured will likely have to be done in the far east to keep the prices low. Your interest in an Uno+ version is noted though.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

Post Reply