Search found 9 matches

by ThierryM
Wed Feb 04, 2015 3:20 pm
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi,
I've tested with a HC3DPR0006 module (bought here with the discount) and I haven't any problem : this SD card reader works fine.
So the SD card reader of the HC3DPR0005 was effectively faulty.
Regards,

Thierry
by ThierryM
Thu Jan 29, 2015 12:10 pm
Forum: HobbyComponents.com shop
Topic: "I only need 10" ?
Replies: 2
Views: 16141

Re: "I only need 10" ?

Thanks, regards,

Thierry
by ThierryM
Wed Jan 28, 2015 6:25 pm
Forum: HobbyComponents.com shop
Topic: "I only need 10" ?
Replies: 2
Views: 16141

"I only need 10" ?

Hi,
On the store for this item http://hobbycomponents.com/hardware/482 ... ts-50-pack, there's the mention "I only need 10" that you can't remove. What's the meaning ?
It's 50 or 10 pieces ?
Thanks for your reply, regards,

Thierry
by ThierryM
Sat Jan 10, 2015 8:56 am
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi,
I've tested all the pins with my working adaptor as model : I've the same results -> the adaptor seems good.
I can't use my working adaptor with your module because the ribbon cables are reverse protected and the plugs aren't in the same direction.
by ThierryM
Fri Jan 09, 2015 8:34 pm
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi,
No problem with the ribbon cables. I can't test with my other jonction board with the Ramps (no same pluggin directions) but with my multimeter I didn't detect any anomaly on it.
Regards,

Thierry
by ThierryM
Tue Jan 06, 2015 11:44 am
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi,
I've reformatted the card in differents formats (Fat16 & Fat32) but the problem is always present. Besides my other LCD controller can read it.
I've an other ribbon câble (working with my Full Graphic LCD controller) and I'll test with it to see if the connections are correct.
Regards,

Thierry
by ThierryM
Mon Jan 05, 2015 8:35 pm
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi, I've tested this module with an other Ramps 1.4 under 12V and the problem is the same : the card is physically detected but the reading is impossible.
Regards,

Thierry
by ThierryM
Mon Jan 05, 2015 12:34 pm
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi, Thanks for your reply. Yes it's a connected to a Ramps 1.4 shield with a Taurino Power from RepRapDiscount working under 24V. I'll install your module with my other Ramps 1.4 and Taurino Classic (currently it's a configuration with a Full Graphic Smart LED Controller and its SD Card reader worki...
by ThierryM
Mon Jan 05, 2015 12:29 am
Forum: 3D Printing / CNC
Topic: RAMPS compatible LCD controller module (HC3DPR0005)
Replies: 16
Views: 57417

Re: RAMPS compatible LCD controller module (HC3DPR0005)

Hi, I use this module for my Reprap Prusa under Marlin. All is working well except the SD card reader. The card is detected physicaly (card detected) but it can't be read. I've tried 2 different SD Cards (2 Go Transcend and 16 Go Sandisk) but both aren't working. I think it's not these cards because...

Go to advanced search