Reply to topic  [ 106 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10, 11  Next
Pic - K150 ICSP Programmer (HCDVBD0002) 
Author Message

Joined: Wed Apr 02, 2014 11:54 pm
Posts: 2
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
hi guys, i have a k150 pic programmer like in the photo on the first page. i have installed the profilic diver 1.9 an the k150 sw english version. but when i try to program my pic 16F628A i have a " recived data error.About to apply reset.." .i have win7 32 bit on my laptop. i also changed the program delay from 50 to 70, in the chipdata.cid.
i would to attach the hex file, but i can't to do it.

please, someone help me.. it drive me crazy..
thanks


Thu Apr 03, 2014 12:18 am
Profile
Site Admin

Joined: Sun Aug 05, 2012 4:15 pm
Posts: 780
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
If you didn't buy the programmer from us it may be that you need a different version of software. Try going to HELP->Protocol and checking that both the software and firmware match.

_________________
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.


Thu Apr 03, 2014 10:43 am
Profile

Joined: Wed Apr 02, 2014 11:54 pm
Posts: 2
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
hi andrew, thanku so much for your replay.
i have MicroBrn P18A Firmware P18A. system is matched
Image


Sat Apr 05, 2014 8:45 am
Profile

Joined: Mon Mar 31, 2014 7:53 pm
Posts: 4
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
iam having trouble with this device cant write anything reads the chip which is 16f631 tried the prog delay its now 110 still no joy any ideas everything downloaded from this site


Sat Apr 05, 2014 5:30 pm
Profile

Joined: Mon Mar 31, 2014 7:53 pm
Posts: 4
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
iam having trouble with this device cant write anything reads the chip which is 16f631 tried the prog delay its now 110 still no joy any ideas everything downloaded from this site


Sat Apr 05, 2014 5:30 pm
Profile
Site Admin

Joined: Sun Aug 05, 2012 4:15 pm
Posts: 780
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
@ciko2k

The error message you are getting is typical of a programming delay time that is too short but it isn't forced to be the cause of the problem. We have however tested the same version of pic ourselves and we know it works fine with our programmers so long as you increase the delay time. A setting of 70 fixed the problem for us but it is work trying larger time delays just in case it is still that causing the problem.

@clvbanks

I've read your email. Could you tell me what the error message is saying?

_________________
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.


Mon Apr 07, 2014 10:05 am
Profile

Joined: Mon Apr 07, 2014 2:52 pm
Posts: 2
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
Hi

When I try to load a hex file I get the error message error in hex file fuse link line 1043 chip set is 18f2550 red led is on

Pete


Mon Apr 07, 2014 4:39 pm
Profile
Site Admin

Joined: Sun Aug 05, 2012 4:15 pm
Posts: 780
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
@peterstorey

Following on from our previous correspondence, could you possibly email a copy of your hex file to support (AT) hobbycomponents.com. I'll take a look at it and see if there's anything obvious with it.

_________________
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.


Tue Apr 08, 2014 8:08 am
Profile

Joined: Mon Apr 07, 2014 2:52 pm
Posts: 2
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
Andrew sorted it out I ran the hex file through the fix file in the downloaded zip file and then it loads awaiting for the chips to be delivered so can not program as yet looks like you need to do it for the 18F series of chips


Tue Apr 08, 2014 12:45 pm
Profile
Site Admin

Joined: Sun Aug 05, 2012 4:15 pm
Posts: 780
Post Re: Pic - K150 ICSP Programmer (HCDVBD0002)
@peterstorey

Ok, great. I believe this only needs to be done for hex files complied for 18 series pic's, and then only for some hex files that have an odd byte count which your file must have had. Anyway glad it fixed the problem for you.

_________________
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.


Thu Apr 10, 2014 7:55 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 106 posts ]  Go to page Previous  1 ... 4, 5, 6, 7, 8, 9, 10, 11  Next

Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Thank you to phpBB.com & phpBB.ro.
Design created by Florea Cosmin Ionut.
© 2011 All contents of this site are © Hobby Components LTD