1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU0059)

LCD, TFT, OLED, LED modules
microbby
Posts: 7
Joined: Mon Jul 11, 2016 12:55 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by microbby » Wed Nov 02, 2016 4:55 pm

Hello
I am not able to find the complete datasheet of this display, in particular the duration in hours at various levels of contrast and the relationship with the values to be sent to the display to get it.
Looking forward to your reply, thank you, Marco

andrew
Site Admin
Posts: 1374
Joined: Sun Aug 05, 2012 4:15 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by andrew » Thu Nov 03, 2016 12:40 pm

I've taken a quick look though the datasheet for the screen itself and it looks to me that the screen life will be effected by two things, the reference current at Iref which is fixed fixed to a specific value by a resistor on the module, and the contrast setting which is set by software. However the datasheet doesn't give any specific settings to display life parameters. Here is what it says about display life:

Life Time (120 cd/m2) = 10,000 hour
Life Time (80 cd/m2) = 30,000 hour
Life Time (60 cd/m2) = 50,000 hour


VCC = 12.0V, Ta = 25°C, 50% Checkerboard.
End of lifetime is specified as 50% of initial brightness reached. The average operating lifetime at room temperature is estimated by the accelerated operation at high temperature conditions.

However I need to contact the manufacture to confirm that the display datasheet we have is correct for the currently shipped displays. They are based in China so so I'll will post here when we get confirmation.
Last edited by andrew on Tue Nov 08, 2016 4:11 pm, edited 1 time in total.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

microbby
Posts: 7
Joined: Mon Jul 11, 2016 12:55 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by microbby » Tue Nov 08, 2016 8:51 am

Thanks, I will wait for the complete datasheet.

Looking for ward, MC

microbby
Posts: 7
Joined: Mon Jul 11, 2016 12:55 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by microbby » Tue Nov 08, 2016 8:51 am

Thanks, I will wait for the complete datasheet.

Looking for ward, MC

andrew
Site Admin
Posts: 1374
Joined: Sun Aug 05, 2012 4:15 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by andrew » Tue Nov 08, 2016 4:07 pm

I've attached an additional datasheet to the first post (GMO13002-4PIN(1_3) SERIES Spec.pdf) which I've just revived from the manufacture. As previously mentioned it provides display life data based on display brightness but there isn't any specific data for display life for different config setting I'm afraid.

I'm also updating my previous post based on the information in this datasheet.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

microtec
Posts: 1
Joined: Tue Sep 13, 2016 11:22 am

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by microtec » Wed Mar 29, 2017 1:10 pm

Hello,
I'm doing some test by changing the contrast register (81h) and writing values from 00h to FFh.
Is it normal that if I set the register to low values (00h to 05h) the brightness is about at 50% of the maximum ?
I expected to have a display almost off with a brightness less than 10%.

Thank you
Maurizio

andrew
Site Admin
Posts: 1374
Joined: Sun Aug 05, 2012 4:15 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU005

Post by andrew » Wed Mar 29, 2017 3:06 pm

I've just given it a quick try myself and I get the same behavior as you, the display is about half contrast with a value of zero. The data sheet is unfortunately not very clear on what to expect. It gives an equation that indicates the ISEG current will be 0 with a register value of 0x00 but then slightly further down there is a table which implies there will still be a 'small' amount of current driving the display. All I can say is I get them same results as you so it's probably the correct behavior.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

GuitarPhil
Posts: 7
Joined: Mon Jan 19, 2015 3:47 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU0059)

Post by GuitarPhil » Sat Feb 16, 2019 5:11 pm

While testing one of the HCMODU0058 1.3" UOLED displays I accidentally discovered that it somehow works without connecting the GND and VCC pins to a power source!

I've repeated this with a number of similar 1.3" SH1106-based OLED modules and they all work even if GND and VCC are left unconnected. I wouldn't believe this myself so here's a link to a photo to prove it!

https://app.box.com/s/38ahkz5cxrv5diivkjuhtealrread76o

Can anyone explain this? Have I discovered a hitherto unknown energy source or am I going nuts?!?! :D :shock:

Phil.

andrew
Site Admin
Posts: 1374
Joined: Sun Aug 05, 2012 4:15 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU0059)

Post by andrew » Mon Feb 18, 2019 1:40 pm

Because these modules are so low power there's probably enough leakage from the internal circuitry on to the supply rails (probably via the ESD protection diodes on the I/O cells) to power the display. It does go without saying that it's not recommended to do this of course.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.

philcoll99
Posts: 2
Joined: Tue May 05, 2020 7:56 pm

Re: 1.3" SH1106 uOLED Display Module (HCMODU0058 & HCMODU0059)

Post by philcoll99 » Sat Sep 12, 2020 1:29 pm

Hi, I’m new to Arduino electronics so this is probably a stupid question! I’ve bought a Wemos D1 ESP8266 controller (HCDVBD0028) and I’m trying to connect this SH1106 display to it, using SPI. Can anyone tell me the connections I need to make between the board and the display? Thanks.

Post Reply

Return to “Display”