Page 1 of 1

4 Chan 433MHz wireless receiver with remote fob (HCWILS0003)

Posted: Thu Mar 02, 2017 11:29 am
by admin
Image



This item is a wireless 4 channel remote controlled module with a battery operated transmitter fob. The fob has 4 individual buttons which, when pressed, will trigger one of the 4 digital output pins on the receiver module. When no buttons are pressed all 4 digital pins will remain low (0V). When one of the transmitter buttons is pressed the appropriate output pin on the receiver will go high (5V) and will remain high until the button is released.

These units are based on the PT2262 & PT2272 433MHz transmitter and receiver IC which means they are compatible with our 433MHz PT2262 wireless transmitter/receiver module. See items HCMODU0048 & HCMODU0049.

The transmitter module includes a 12V 23AE alkaline battery and the receiver module can be powered by a single 5V DC supply.


Notes:

To obtain maximum receiver range an external antenna should be attached to the ANT pad on the receiver module. We recommend a length of single core wire measuring 23.8cm (1/4 wavelength) in length.

This is a short range device operating in the 433MHz spectrum. As with all wireless transmitters please make sure this device is legal to operate within your country.


Image


Features:

Product code: HCWILS0004
Operating frequency: 433MHz
Max range: ~10 Meters in free space
Remote: Key ring fob with 4 push buttons and extendable antenna.
Remote control power: Battery operated (12V 23AE included)
Receiver: 4 Channel module capable of receiving a trigger signal from multiple transmitters (Note only one channel can be activated at any one time).
Receiver power: 5V DC via screw terminals
Receiver outputs: 5V TTL active high.


Receiver Pinout:

1) GND.......Power 0V
2) 5V..........Power +5V
3) D0.........Digital output 1 (high when button B is pressed)
4) D1.........Digital output 1 (high when button D is pressed)
5) D2.........Digital output 1 (high when button A is pressed)
6) D3.........Digital output 1 (high when button C is pressed)
7) VT.........Valid Transmission (high = valid transmission received)


Downloads:
PT2272.pdf

Disclaimer: Libraries, example code, and diagrams are provided as an additional free service by Hobby Components and are not sold as part of this product. We do not provide any guarantees or warranties as to their accuracy or fitness for purpose. Diagrams are for illustration purposes only and may not be to scale.

Copyright notice: Descriptions and diagrams on this page are copyright Hobby Components Ltd and may not be reproduced without permission.

Re: 4 Chan 433MHz wireless receiver with remote fob (HCWILS0

Posted: Mon Mar 06, 2017 8:39 am
by mmcp42
nice looking module
couple of questions:
a) is the 7-pin header already connected?
would be handy if it wasn't!
b) how do you set the "address"?

thanks

Re: 4 Chan 433MHz wireless receiver with remote fob (HCWILS0

Posted: Mon Mar 06, 2017 3:34 pm
by andrew
a) is the 7-pin header already connected?
Yes the module is supplied with the connector already soldered.
b) how do you set the "address"?
Both the fob and the module come with are supplied already configured to the same (randomly selected by the manufacturer) address so there is no need to program them. However if you wanted to change the address there is a set of pads on the back of the module and and similar set on the PCB inside the fob. You set the address applying solder bridge(s) to them.

Re: 4 Chan 433MHz wireless receiver with remote fob (HCWILS0

Posted: Mon Mar 06, 2017 4:22 pm
by mmcp42
hello Andrew
thanks for the rapid response
I can live with all of that
cheers!