Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST0006)
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
I've no idea why it would have those VID and PID's. My only guess is that it is something that was left in by the factory. I've sent you an email so hopefully we can have this problem fixed quickly.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.
-
- Posts: 3
- Joined: Fri Oct 09, 2015 2:58 pm
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
Thank you Andrew!
The instructions and links to latest downloads you sent via PM has done the trick with this device - re-flashed with the FX2 image.
After all my previous messing about, I had to dig-deep in to Windows to expunge the previous driver files and associated INF files before the final step of loading the FX2 drivers would succeed and then allow PulseView to recognise the device - which now appears as 'Cypress FX2' in the analyser.
That was fun - thanks again!
Terrific support and service - for what is unlikely to be a particularly profitable sale for HC!
I'll make sure to rate that in my eBay feedback
Happy weekend!
M.
The instructions and links to latest downloads you sent via PM has done the trick with this device - re-flashed with the FX2 image.
After all my previous messing about, I had to dig-deep in to Windows to expunge the previous driver files and associated INF files before the final step of loading the FX2 drivers would succeed and then allow PulseView to recognise the device - which now appears as 'Cypress FX2' in the analyser.
That was fun - thanks again!
Terrific support and service - for what is unlikely to be a particularly profitable sale for HC!
I'll make sure to rate that in my eBay feedback
Happy weekend!
M.
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
That's great. Glad we managed to find a solution and sorry for any inconvenience caused.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
Can these additional steps and firmware flash be made public? The driver does not install on win7 or win10 (it results in a failed install, and manual inf install fails too).
Reports as USB\VID_04B4 & PID_8613, but the driver on the original thread just fails to install anything.
Reports as USB\VID_04B4 & PID_8613, but the driver on the original thread just fails to install anything.
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
The PID and VID are correct so I doubt your issue is the same. The fx2lafw driver in the first post should defiantly work on your windows 7 system. If you have a spare micro USB cable can you try it in case it's causing the problem. We do see problems caused by USB cables from time to time so it's worth a try.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
I've tried multiple known good cables on both systems, the problem is definitely with the driver. Regardless of which executable is run, a command window flashes up, followed by windows 'this program might not have installed correctly' prompt. A command prompt flashes up momentarily, but disappears before you can see what it says, and the message does not appear when invoked from a command prompt. This occurs on both systems, both are x64 installs, fwiw.andrew wrote:The PID and VID are correct so I doubt your issue is the same. The fx2lafw driver in the first post should defiantly work on your windows 7 system. If you have a spare micro USB cable can you try it in case it's causing the problem. We do see problems caused by USB cables from time to time so it's worth a try.
(a manual inf install also fails)
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
The drivers have been tested with both 32 and 64 bit versions of windows 7 so I'm a little puzzled as to why there is an issue. In device manager do you see the analyser listed? For a correct install it is usually under 'Universal Serial Bus devices' as fx2lafw. Do you see it there or anywhere else and if so is it reporting any errors?
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
We've had a breakthrough! On the windows 7 machine it was coming up as unknown device; The inf would not be accepted in the update drivers 'have disk' box, but amazingly, it found a driver on windows update which worked. I think that's the first time finding a driver via windows update has _ever_ worked
Anyway, am now tinkering, many thanks! After the driver installed it worked first time capturing some UART traffic.
Cheers!
Anyway, am now tinkering, many thanks! After the driver installed it worked first time capturing some UART traffic.
Cheers!
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
Hi All,
I purchased the 8 channel one from ebay a few days ago, installed the latest pulseview windows 7 executable and the driver on the hobby electronics github repo and everything works fine in the sense that the analyzer is picking up signals etc. However, there is an issue where pulseview just stops sampling. So it will run after clicking 'run' for about 30 - 50 seconds and then just stops. I was wondering if anyone else had experienced this before and if anyone had any ideas as to the cause? Fantastic tool by the way, getting what seem to be very accurate readings! Many thanks
I purchased the 8 channel one from ebay a few days ago, installed the latest pulseview windows 7 executable and the driver on the hobby electronics github repo and everything works fine in the sense that the analyzer is picking up signals etc. However, there is an issue where pulseview just stops sampling. So it will run after clicking 'run' for about 30 - 50 seconds and then just stops. I was wondering if anyone else had experienced this before and if anyone had any ideas as to the cause? Fantastic tool by the way, getting what seem to be very accurate readings! Many thanks
Re: Hobby Components USB 8CH 24MHz Logic Analyser (HCTEST000
It could simply be a bad USB cable. If you have a spare one could you try that. Also if your plugging it into a USB HUB try plugging it directly into your computer.
Comments made by this poster do not necessarily reflect the views of Hobby Components Ltd.